11744 NE Ainsworth Circle
Portland, OR 97220
Google Maps
503-257-7500
1-800-444-6473
|
 |
Volvo C70 1998-2005 » Upper Engine Stabilizer Mount
 The original rubber engine stabilizer mount has proven to be a weak link that that can fail prematurely and allow the engine to rock and move during acceleration and braking, significantly affecting the handling and performance of the car. This mount is located near the top of the engine on the backside just to the right of center, connecting the engine to the firewall. The original mount requires a special Volvo press tool for removal and installation.
Our improved polyurethane material is stronger (we warranty it for life) and the 2 piece design allows for easy installation without special tools. The original mount is covered under the basic Volvo warranty, however we have heard from customers that have had the original rubber mount replaced several times. To inspect your mount, look for signs of the rubber separating where it is attached to the outer housing. The original rubber bushing can be removed and our HD replacement can be installed in about 30 minutes with common hand tools and included instructions.
Please note!
These polyurethane bushings are firmer than the stock rubber parts they replace and can transmit additional vibration in some cases. Especially if the motor mounts and or transmission mounts are worn. When you replace the worn out rubber mount, now much of the load is supported by the new stiffer bushing and this can often lead to unwanted vibration, especially at idle on models equipped with automatic transmissions. It’s important to make sure that your other mounts are in good condition to avoid unwanted vibration.Please check fitment listed below to ensure products will fit your specific vehicle.
Some products may include or exclude some model years or engine and transmission combinations. Click here to report errors, pricing problems or missing applications.
2B1850 Reviewed by Spencer Liddle from Buckley, WA 98321
All I can say is wow. Get one. Now.
June 2008
2B1850 Reviewed by Nathan from Virginia Beach VA
Easy to install only took about 15 mins with minor tools ( 2 wrenches,keyhole saw,flathead and hammer) repaced my oem bushing on my 850 which was shot.I would definently recommend this to anyone due to the quality of this product and the easy installation
June 2008
2B1850 Reviewed by Tom Vinzent from Orinda, California
2B1850-upper Engine Stabilizer Mount; On my 2000 Volvo V70, I was having a noise problem when going up a sweeping freeway on-ramp. There was an engine noise that sounded like a dry bearing. When I took my foot off the gas, the noise stopped. The local Volvo dealer thought it might be a loose brake backing plate; one independent shop thought it was a bad wheel bearing (even though I told them the noise stopped when I took my foot off the gas). The third shop didn't give an opinion. All three shops noted that I needed an upper engine mount. The dealer said a new mount would not solve the noise problem. Since everyone seemed to be guessing, I didn't fix the noise problem. However, I purchased the IPD engine mount, and easily installed it, and to my surprise, it cured the noise problem. It must be that the engine was pulling off center on the on-ramps, and something (crank maybe) was scraping the oil pan. The new IPD mount solved the problem Haven't heard the noise in 6-months. Fixed what could have been a major expense (in the shop's eyes) for $26.00 As many have noted, there is a vibration when coming to a stop, but that is bearable. No vibration at all on the road.
ipd customer service response: Generally the vibration occurs while idling at a stop.
June 2008
2B1880 Reviewed by Matthew L. Blair from Midlothian, Virginia
I finally received my polyurethane bushing today. THANK YOU IPD!!!! After my mechanic installed the new polyurethane bushing I could feel a significant change in the driving of my 2000 XC SE within the 15 minute commute to work. Awesome part, and awesome customer service. Thank you IPD, thank you very much.
ipd customer service response: We're sorry about the delay but glad you like the product!
May 2008
2B1880 Reviewed by Jay from Atlanta, GA
This is the second application of the poly bushing I've used. Installed it previously on my 95 850 and now on my 05 S60. In both cases, the results were very noticeable when driving. The car just has a tighter, more confident feel about it that didn't exist before. The vibration is noticeable at idle, however. Shifting to neutral seems to help. Other than that, both applications have been a joy to have.
May 2008
2B1850 Reviewed by Aaron from Lancaster, PA
Old mount was very very stubborn required professional assistance, other than that it looks and works great! I feel it's at a very fair price. About the vibration noted in the description.....I notice no foreign vibration just smooth torque when the gas is applied. This mount gets a A+++++ for sure. Thanks IPD.
April 2008
2B1850 Reviewed by MARCUSANTONUS from PACIFICA CA
Simple to install, feels good inside and looks nice next to IPD wires.
April 2008
2B1880 Reviewed by Bill from Sandy
Update from Bill from Sandy.
In order to cure the severve vibration I mentioned in my earlier review I ended having to go back to all Volvo OE parts: upper engine mount and lower torque rod. I have given up slightly better handling and response but the vibration was too much to live with.
March 2008
2B1880 Reviewed by Bill from Sandy, Utah
The upper engine stabilizer mount in 2001 S60 blew out at about 40,000 miles. I replaced it with the IPD part and was very happy with results; easy to install. Since then I installed the QBM strut bar conversion and the HD poly transmission mount (the busing on the OE was amost gone at 70,000 miles). I noticed a slight improvement in throttle response and a little less body flex when cornering. The negative is that I have developed a very severe vibration at idle (in gear, neutral is okay) and when accelerating between 1,300 and 1,800 rpm. Two separate volvo mechanics tell me it is the combination of the IPD exhaust and changing to a harder bushings. I am in the process of backtracking and changing to OE parts to try and reduce the vibration.
March 2008
2B1850 Reviewed by Russell Mojica from NY
I installed this on my 1993 850 5 speed. This mount is a must for anyone. I orderd this along with the poly filled firewall mount, and the assembled lower poly Tranny torque mount. I love all the added feel of the motor. I dont like cushy stock mounts >:{> I love these mounts!!!
February 2008
To leave your own Review, Drill down on the specific product above.
|
